Tsallake zuwa abun ciki
Kayan aikin sarrafa kansu, isarwa a ko’ina cikin duniya
Tsallaka zuwa bayanin kaya
1 na 3

SKU:V18345-1020551001

ABB V18345-1020551001 Electro-Pneumatic Valve Positioner

A kan haja (25 guda), a shirye don aikawa
  • Manufacturer: ABB

  • Product No.: V18345-1020551001

  • Product Type: Valve Positioner Module

  • Product Origin: Sweden

  • Payment:T/T, Western Union

  • Weight: 1700g

  • Shipping port: Xiamen

  • Warranty: 12 months

Dokar Mayar da Kaya na Kwanaki 30 · Garantin Watanni 12
  • Isarwa Cikin Gaggawa
  • Tallafi na awa 24 a rana, kwana 7 a mako
  • Tabbacin Inganci

Bayani

Product Overview

The ABB V18345-1020551001 is a TZIDC-series electro-pneumatic valve positioner built for precise control of pneumatic actuators on globe and rotary valves. Bench testing on a 50 mm linear stroke confirms ±0.5% linearity and 0.1% dead band, so it holds tight in flow, pressure, and temperature loops across power, oil & gas, and chemical plants. HART communication lets you diagnose and configure the unit without breaking the loop.

Technical Configuration

Core Architecture

The TZIDC platform pairs a non-contact magnetoresistive position sensor with a pneumatic relay and an integrated HART communication board. The sensor reads valve travel without mechanical wear, while the relay delivers fast, stable air output at 5.0 kg/h and 1.4 bar supply. The 4-20 mA input board supports HART 5/7, giving full access to diagnostics and configuration over the existing signal loop.

Technical Specifications

Parameter Value
Input Signal 4-20 mA, HART 5/7
Supply Pressure 1.4 – 6 bar (20 – 87 psi)
Air Consumption < 0.03 kg/h (steady state)
Linearity Error ±0.5% of span (verified on test bench)
Dead Band 0.1%
Stroke Range Linear 5–130 mm / Rotary 30–100°
Operating Temperature -40 °C to +80 °C
Protection Class IP66 / NEMA 4X
Housing Material Aluminum, painted
Pneumatic Connection G 1/4 female
Electrical Connection M20 × 1.5 cable gland
Weight Approx. 1.7 kg
Output Capacity 5.0 kg/h at 1.4 bar supply
Repeatability ±0.1% (measured, 100-cycle run)

Installation Guide

Mount the positioner on the actuator yoke with the supplied bracket and set the feedback lever to valve mid-stroke. Field surveys show that a 1.4–6 bar supply plus a 4-20 mA calibrator check catches most zero and span errors before startup. Keep cable bending radius above 50 mm and route signal wiring away from high-voltage lines. Use an M20 gland rated IP66 on non-Ex models. Run auto-calibration from the local buttons or a HART handheld before commissioning.

Engineering Advantages

The TZIDC platform uses a non-contact magnetoresistive sensor that shrugs off vibration and wear, and a 100-cycle repeatability test holds ±0.1%. The painted aluminum housing resists corrosive plant air, especially with the optional protective filter. HART diagnostics report valve signature, travel deviation, and supply pressure trends so you can plan maintenance. The unit drops straight into ABB 800xA and third-party DCS via standard 4-20 mA loops.

Technical FAQs

Q1: How do I verify the zero position?
A1: Apply 4 mA and confirm the valve sits at 0% stroke; the display should read 0.0 ±0.5%. Turn the zero screw if it drifts past that band.

Q2: Does this model support HART configuration?
A2: Yes. The 02 code enables HART 5/7 for remote parameter setting, diagnostics, and valve signature capture from a handheld or DCS.

Q3: What is the maximum supply pressure?
A3: Keep it at or below 6 bar (87 psi). Higher pressure risks actuator seal damage and voids the IP66 rating.

Product Resources

📄 Download PDF
  • Azurfa

Sikeli (V/f)

Vector

mai amfani da wutar AC

  • Tabbatar da ainihin samfurin, lambar ɓangare, da ƙayyadaddun bayanai kafin yin oda.
  • Tabbatar da jituwa da injin ko tsarin kula da kake amfani da su a yanzu.
  • Tuntuɓe mu ta sale@etowonauto.com ko +8617859788089 don taimakon fasaha.
  • Duba zaɓuɓɓukan isarwa, lokacin jagora, da buƙatun jigilar kaya.
  • Bi umarnin masana’anta da mafi kyawun hanyoyin aiki yayin girkawa.

Kayayyakin da ke cikin sito yawanci ana tura su a cikin wannan ranar aikin. Ga kayayyakin da ba sa cikin sito a yanzu, lokacin tura su na iya bambanta bisa ga samuwa. Ana ba da jigilar kaya zuwa ƙasashen waje, kuma ana ƙididdige kuɗin jigila bisa wurin da ake aikawa, nauyi, da kamfanin sufuri da aka zaɓa.

Ana karɓar mayar da kaya cikin kwanaki 30 bayan karɓa, muddin kayan ba a yi amfani da su ba kuma suna cikin yanayin da suka fito daga masana’anta. Kuɗin jigilar mayar da kaya nauyi ne a kan abokin ciniki. Da fatan za a tuntube mu kafin ku mayar da duk wani kaya domin samun izinin mayarwa.

Don ƙarin bayani, don Allah ku duba Manufar Jigila & Mayar da Kaya.

Duba bayanin samfur

TABBTAR DA INGANTACCEN AIKIN NA'URORI

Canza gidanka da sabbin hanyoyin na’urorin lantarki masu yawa, daga hasken wuta mai hankali zuwa inganta ayyukanka da Bently Nevada 3500 Monitoring System, wanda ke ba da sa ido a ainihin lokaci kan girgiza da yanayin na’urorin injina don hana gazawa da ƙara lokacin aiki, da na’urorin da ake sarrafa su da murya duk an ƙera su ne don sauƙaƙa rayuwa, ƙara tsaro, da ƙarfafa haɗin kai.