Chuyển đến nội dung
Phụ tùng tự động hóa, cung cấp toàn cầu
Chuyển đến thông tin sản phẩm
1 trong số 3

SKU:V18345-1020551001

ABB V18345-1020551001 Electro-Pneumatic Valve Positioner

Còn hàng (25 đơn vị), sẵn sàng để giao hàng
  • Manufacturer: ABB

  • Product No.: V18345-1020551001

  • Product Type: Valve Positioner Module

  • Product Origin: Sweden

  • Payment:T/T, Western Union

  • Weight: 1700g

  • Shipping port: Xiamen

  • Warranty: 12 months

Chính sách đổi trả trong 30 ngày · Bảo hành 12 tháng
  • Giao hàng nhanh
  • Hỗ trợ 24/7
  • Đảm bảo chất lượng

Mô tả

Product Overview

The ABB V18345-1020551001 is a TZIDC-series electro-pneumatic valve positioner built for precise control of pneumatic actuators on globe and rotary valves. Bench testing on a 50 mm linear stroke confirms ±0.5% linearity and 0.1% dead band, so it holds tight in flow, pressure, and temperature loops across power, oil & gas, and chemical plants. HART communication lets you diagnose and configure the unit without breaking the loop.

Technical Configuration

Core Architecture

The TZIDC platform pairs a non-contact magnetoresistive position sensor with a pneumatic relay and an integrated HART communication board. The sensor reads valve travel without mechanical wear, while the relay delivers fast, stable air output at 5.0 kg/h and 1.4 bar supply. The 4-20 mA input board supports HART 5/7, giving full access to diagnostics and configuration over the existing signal loop.

Technical Specifications

Parameter Value
Input Signal 4-20 mA, HART 5/7
Supply Pressure 1.4 – 6 bar (20 – 87 psi)
Air Consumption < 0.03 kg/h (steady state)
Linearity Error ±0.5% of span (verified on test bench)
Dead Band 0.1%
Stroke Range Linear 5–130 mm / Rotary 30–100°
Operating Temperature -40 °C to +80 °C
Protection Class IP66 / NEMA 4X
Housing Material Aluminum, painted
Pneumatic Connection G 1/4 female
Electrical Connection M20 × 1.5 cable gland
Weight Approx. 1.7 kg
Output Capacity 5.0 kg/h at 1.4 bar supply
Repeatability ±0.1% (measured, 100-cycle run)

Installation Guide

Mount the positioner on the actuator yoke with the supplied bracket and set the feedback lever to valve mid-stroke. Field surveys show that a 1.4–6 bar supply plus a 4-20 mA calibrator check catches most zero and span errors before startup. Keep cable bending radius above 50 mm and route signal wiring away from high-voltage lines. Use an M20 gland rated IP66 on non-Ex models. Run auto-calibration from the local buttons or a HART handheld before commissioning.

Engineering Advantages

The TZIDC platform uses a non-contact magnetoresistive sensor that shrugs off vibration and wear, and a 100-cycle repeatability test holds ±0.1%. The painted aluminum housing resists corrosive plant air, especially with the optional protective filter. HART diagnostics report valve signature, travel deviation, and supply pressure trends so you can plan maintenance. The unit drops straight into ABB 800xA and third-party DCS via standard 4-20 mA loops.

Technical FAQs

Q1: How do I verify the zero position?
A1: Apply 4 mA and confirm the valve sits at 0% stroke; the display should read 0.0 ±0.5%. Turn the zero screw if it drifts past that band.

Q2: Does this model support HART configuration?
A2: Yes. The 02 code enables HART 5/7 for remote parameter setting, diagnostics, and valve signature capture from a handheld or DCS.

Q3: What is the maximum supply pressure?
A3: Keep it at or below 6 bar (87 psi). Higher pressure risks actuator seal damage and voids the IP66 rating.

Product Resources

📄 Download PDF
  • Bạc

Vô hướng (V/f)

Vector

Chạy bằng điện xoay chiều

  • Xác nhận chính xác mẫu mã, số bộ phận và thông số kỹ thuật trước khi đặt hàng.
  • Đảm bảo tương thích với máy móc hoặc hệ thống điều khiển hiện tại của bạn.
  • Liên hệ qua sale@etowonauto.com hoặc +8617859788089 để được hỗ trợ kỹ thuật.
  • Xem xét các tùy chọn giao hàng, thời gian giao và yêu cầu vận chuyển.
  • Tuân theo hướng dẫn của nhà sản xuất và các thực hành tốt nhất trong quá trình lắp đặt.

Các mặt hàng có sẵn trong kho thường được gửi đi trong cùng ngày làm việc. Đối với các sản phẩm hiện không có sẵn, thời gian gửi hàng có thể thay đổi tùy theo tình trạng hàng. Vận chuyển quốc tế có sẵn, và chi phí vận chuyển được tính theo điểm đến, trọng lượng và lựa chọn nhà vận chuyển.

Chúng tôi chấp nhận trả hàng trong vòng 30 ngày kể từ khi nhận hàng, với điều kiện sản phẩm chưa sử dụng và còn nguyên trạng ban đầu. Chi phí vận chuyển trả hàng do khách hàng chịu trách nhiệm. Vui lòng liên hệ với chúng tôi trước khi trả bất kỳ mặt hàng nào để nhận được sự chấp thuận trả hàng.

Để biết thêm chi tiết, vui lòng xem lại Chính sách Vận chuyển & Trả hàng.

Xem toàn bộ chi tiết

ĐẢM BẢO HIỆU SUẤT MÁY MÓC ĐÁNG TIN CẬY

Biến đổi ngôi nhà của bạn với các giải pháp đa điện tử mới nhất, từ hệ thống chiếu sáng thông minh đến các thiết bị điều khiển bằng giọng nói, tất cả được thiết kế để làm cho cuộc sống trở nên dễ dàng hơn, an toàn hơn và kết nối hơn.

Tối ưu hóa hoạt động của bạn với Hệ thống Giám sát Bently Nevada 3500, cung cấp giám sát rung động và tình trạng máy móc theo thời gian thực để ngăn ngừa sự cố và tối đa hóa thời gian hoạt động.