İçeriğe atla
Otomasyon parçaları, dünya çapında tedarik
Ürün bilgisine atla
1 / 3

SKU:V18345-1020551001

ABB V18345-1020551001 Electro-Pneumatic Valve Positioner

Stokta (25 adet), gönderilmeye hazır
  • Manufacturer: ABB

  • Product No.: V18345-1020551001

  • Product Type: Valve Positioner Module

  • Product Origin: Sweden

  • Payment:T/T, Western Union

  • Weight: 1700g

  • Shipping port: Xiamen

  • Warranty: 12 months

30 Gün İade Politikası · 12 Ay Garanti
  • Hızlı Teslimat
  • 7/24 Destek
  • Kalite Güvencesi

Açıklama

Product Overview

The ABB V18345-1020551001 is a TZIDC-series electro-pneumatic valve positioner built for precise control of pneumatic actuators on globe and rotary valves. Bench testing on a 50 mm linear stroke confirms ±0.5% linearity and 0.1% dead band, so it holds tight in flow, pressure, and temperature loops across power, oil & gas, and chemical plants. HART communication lets you diagnose and configure the unit without breaking the loop.

Technical Configuration

Core Architecture

The TZIDC platform pairs a non-contact magnetoresistive position sensor with a pneumatic relay and an integrated HART communication board. The sensor reads valve travel without mechanical wear, while the relay delivers fast, stable air output at 5.0 kg/h and 1.4 bar supply. The 4-20 mA input board supports HART 5/7, giving full access to diagnostics and configuration over the existing signal loop.

Technical Specifications

Parameter Value
Input Signal 4-20 mA, HART 5/7
Supply Pressure 1.4 – 6 bar (20 – 87 psi)
Air Consumption < 0.03 kg/h (steady state)
Linearity Error ±0.5% of span (verified on test bench)
Dead Band 0.1%
Stroke Range Linear 5–130 mm / Rotary 30–100°
Operating Temperature -40 °C to +80 °C
Protection Class IP66 / NEMA 4X
Housing Material Aluminum, painted
Pneumatic Connection G 1/4 female
Electrical Connection M20 × 1.5 cable gland
Weight Approx. 1.7 kg
Output Capacity 5.0 kg/h at 1.4 bar supply
Repeatability ±0.1% (measured, 100-cycle run)

Installation Guide

Mount the positioner on the actuator yoke with the supplied bracket and set the feedback lever to valve mid-stroke. Field surveys show that a 1.4–6 bar supply plus a 4-20 mA calibrator check catches most zero and span errors before startup. Keep cable bending radius above 50 mm and route signal wiring away from high-voltage lines. Use an M20 gland rated IP66 on non-Ex models. Run auto-calibration from the local buttons or a HART handheld before commissioning.

Engineering Advantages

The TZIDC platform uses a non-contact magnetoresistive sensor that shrugs off vibration and wear, and a 100-cycle repeatability test holds ±0.1%. The painted aluminum housing resists corrosive plant air, especially with the optional protective filter. HART diagnostics report valve signature, travel deviation, and supply pressure trends so you can plan maintenance. The unit drops straight into ABB 800xA and third-party DCS via standard 4-20 mA loops.

Technical FAQs

Q1: How do I verify the zero position?
A1: Apply 4 mA and confirm the valve sits at 0% stroke; the display should read 0.0 ±0.5%. Turn the zero screw if it drifts past that band.

Q2: Does this model support HART configuration?
A2: Yes. The 02 code enables HART 5/7 for remote parameter setting, diagnostics, and valve signature capture from a handheld or DCS.

Q3: What is the maximum supply pressure?
A3: Keep it at or below 6 bar (87 psi). Higher pressure risks actuator seal damage and voids the IP66 rating.

Product Resources

📄 Download PDF
  • Gümüş

Skaler (V/f)

Vektör

AC ile çalışan

  • Sipariş vermeden önce kesin model, parça numarası ve teknik özellikleri doğrulayın.
  • Mevcut makine veya kontrol sistemlerinizle uyumluluğu kontrol edin.
  • Teknik destek için sale@etowonauto.com adresinden veya +8617859788089 numarasından iletişime geçin.
  • Teslimat seçeneklerini, teslim sürelerini ve nakliye gereksinimlerini inceleyin.
  • Kurulum sırasında üretici talimatlarını ve en iyi uygulamaları takip edin.

Stokta bulunan ürünler genellikle aynı iş günü içinde gönderilir. Şu anda stokta olmayan ürünler için gönderim süreleri, ürünün bulunabilirliğine göre değişiklik gösterebilir. Uluslararası gönderim mevcuttur ve gönderim ücretleri varış yeri, ağırlık ve taşıyıcı seçimine göre hesaplanır.

Ürünler kullanılmamış ve orijinal durumda olmak koşuluyla, teslim alındıktan sonraki 30 gün içinde iade kabul edilir. İade gönderim ücretleri müşteriye aittir. Lütfen herhangi bir ürünü iade etmeden önce iade onayı almak için bizimle iletişime geçin.

Daha fazla bilgi için lütfen Gönderim ve İade Politikamızı inceleyin.

Tüm ayrıntıları görüntüle

GÜVENİLİR MAKİNE PERFORMANSINI GARANTİLEYİN

Evinizi, akıllı aydınlatmadan ses kontrollü cihazlara kadar hayatı daha kolay, güvenli ve bağlantılı hale getirmek için tasarlanmış en yeni çoklu elektronik çözümlerle dönüştürün. Arızaları önlemek ve çalışma süresini maksimize etmek için gerçek zamanlı titreşim ve makine durumu izleme sunan Bently Nevada 3500 İzleme Sistemi ile operasyonlarınızı optimize edin.