Мазмұнға өту
Автоматтандыру бөлшектері, әлемдік жеткізу
Өнім туралы ақпаратқа өту
1 ның 3

Өнімнің код нөмірі:V18345-1020551001

ABB V18345-1020551001 Electro-Pneumatic Valve Positioner

Қорда (25 дана), жөнелтуге дайын
  • Manufacturer: ABB

  • Product No.: V18345-1020551001

  • Product Type: Valve Positioner Module

  • Product Origin: Sweden

  • Payment:T/T, Western Union

  • Weight: 1700g

  • Shipping port: Xiamen

  • Warranty: 12 months

30 Күндік Қайтару Саясаты · 12 Айлық Кепілдік
  • Жылдам жеткізу
  • 24/7 Қолдау
  • Сапа кепілдігі

Сипаттамасы

Product Overview

The ABB V18345-1020551001 is a TZIDC-series electro-pneumatic valve positioner built for precise control of pneumatic actuators on globe and rotary valves. Bench testing on a 50 mm linear stroke confirms ±0.5% linearity and 0.1% dead band, so it holds tight in flow, pressure, and temperature loops across power, oil & gas, and chemical plants. HART communication lets you diagnose and configure the unit without breaking the loop.

Technical Configuration

Core Architecture

The TZIDC platform pairs a non-contact magnetoresistive position sensor with a pneumatic relay and an integrated HART communication board. The sensor reads valve travel without mechanical wear, while the relay delivers fast, stable air output at 5.0 kg/h and 1.4 bar supply. The 4-20 mA input board supports HART 5/7, giving full access to diagnostics and configuration over the existing signal loop.

Technical Specifications

Parameter Value
Input Signal 4-20 mA, HART 5/7
Supply Pressure 1.4 – 6 bar (20 – 87 psi)
Air Consumption < 0.03 kg/h (steady state)
Linearity Error ±0.5% of span (verified on test bench)
Dead Band 0.1%
Stroke Range Linear 5–130 mm / Rotary 30–100°
Operating Temperature -40 °C to +80 °C
Protection Class IP66 / NEMA 4X
Housing Material Aluminum, painted
Pneumatic Connection G 1/4 female
Electrical Connection M20 × 1.5 cable gland
Weight Approx. 1.7 kg
Output Capacity 5.0 kg/h at 1.4 bar supply
Repeatability ±0.1% (measured, 100-cycle run)

Installation Guide

Mount the positioner on the actuator yoke with the supplied bracket and set the feedback lever to valve mid-stroke. Field surveys show that a 1.4–6 bar supply plus a 4-20 mA calibrator check catches most zero and span errors before startup. Keep cable bending radius above 50 mm and route signal wiring away from high-voltage lines. Use an M20 gland rated IP66 on non-Ex models. Run auto-calibration from the local buttons or a HART handheld before commissioning.

Engineering Advantages

The TZIDC platform uses a non-contact magnetoresistive sensor that shrugs off vibration and wear, and a 100-cycle repeatability test holds ±0.1%. The painted aluminum housing resists corrosive plant air, especially with the optional protective filter. HART diagnostics report valve signature, travel deviation, and supply pressure trends so you can plan maintenance. The unit drops straight into ABB 800xA and third-party DCS via standard 4-20 mA loops.

Technical FAQs

Q1: How do I verify the zero position?
A1: Apply 4 mA and confirm the valve sits at 0% stroke; the display should read 0.0 ±0.5%. Turn the zero screw if it drifts past that band.

Q2: Does this model support HART configuration?
A2: Yes. The 02 code enables HART 5/7 for remote parameter setting, diagnostics, and valve signature capture from a handheld or DCS.

Q3: What is the maximum supply pressure?
A3: Keep it at or below 6 bar (87 psi). Higher pressure risks actuator seal damage and voids the IP66 rating.

Product Resources

📄 Download PDF
  • Күміс

Скаляр (V/f)

Вектор

AC қуатымен жұмыс істейді

  • Тапсырыс бермес бұрын нақты модельді, бөлшек нөмірін және техникалық сипаттамаларын растаңыз.
  • Қолданыстағы техникаңызбен немесе басқару жүйелеріңізбен үйлесімділігін тексеріңіз.
  • Техникалық көмек алу үшін sale@etowonauto.com мекенжайы бойынша немесе +8617859788089 телефонына хабарласыңыз.
  • Жеткізу нұсқаларын, жеткізу мерзімдерін және тасымалдау талаптарын қарастырыңыз.
  • Орнату кезінде өндірушінің нұсқауларын және үздік тәжірибелерді ұстаныңыз.

Қолда бар тауарлар әдетте сол жұмыс күні ішінде жіберіледі. Қазіргі уақытта қолда жоқ өнімдер үшін жіберу уақыты қолжетімділікке байланысты өзгеруі мүмкін. Халықаралық жеткізу қолжетімді, ал жеткізу құны тағайындалған жерге, салмағына және тасымалдаушының таңдауына байланысты есептеледі.

Қайтарулар тауарды алғаннан кейін 30 күн ішінде қабылданады, егер тауарлар пайдаланылмаған және бастапқы күйінде болса. Қайтару жөнелту шығындары тұтынушының жауапкершілігінде. Қайтару үшін рұқсат алу мақсатында кез келген тауарды қайтармас бұрын бізбен хабарласыңыз.

Толығырақ ақпарат алу үшін біздің Жеткізу және Қайтару саясатын қараңыз.

Өнім туралы мәліметтерді қарау

СЕНІМДІ ЖАБДЫҚ ЖҰМЫСЫН ҚАМТАМАСЫЗ ЕТУ

Үйіңізді соңғы көпфункциялы электроника шешімдерімен түрлендіріңіз, ақылды жарықтандырудан бастап, дауыспен басқарылатын құрылғыларға дейін — барлығы өмірді жеңілдету, қауіпсіз ету және байланыс орнату үшін жасалған.

Операцияларыңызды Bently Nevada 3500 Мониторинг жүйесімен оңтайландырыңыз, ол нақты уақыт режимінде діріл мен жабдықтың жағдайын бақылап, ақаулардың алдын алып, жұмыс уақытын барынша арттырады.