Langkau ke kandungan
Bahagian automasi, bekalan seluruh dunia
Langkau ke maklumat produk
1 daripada 3

SKU:V18345-1020551001

ABB V18345-1020551001 Electro-Pneumatic Valve Positioner

Stok ada (25 unit), sedia untuk dihantar
  • Manufacturer: ABB

  • Product No.: V18345-1020551001

  • Product Type: Valve Positioner Module

  • Product Origin: Sweden

  • Payment:T/T, Western Union

  • Weight: 1700g

  • Shipping port: Xiamen

  • Warranty: 12 months

Polisi Pemulangan 30 Hari · Jaminan 12 Bulan
  • Penghantaran Pantas
  • Sokongan 24/7
  • Jaminan Kualiti

Penerangan

Product Overview

The ABB V18345-1020551001 is a TZIDC-series electro-pneumatic valve positioner built for precise control of pneumatic actuators on globe and rotary valves. Bench testing on a 50 mm linear stroke confirms ±0.5% linearity and 0.1% dead band, so it holds tight in flow, pressure, and temperature loops across power, oil & gas, and chemical plants. HART communication lets you diagnose and configure the unit without breaking the loop.

Technical Configuration

Core Architecture

The TZIDC platform pairs a non-contact magnetoresistive position sensor with a pneumatic relay and an integrated HART communication board. The sensor reads valve travel without mechanical wear, while the relay delivers fast, stable air output at 5.0 kg/h and 1.4 bar supply. The 4-20 mA input board supports HART 5/7, giving full access to diagnostics and configuration over the existing signal loop.

Technical Specifications

Parameter Value
Input Signal 4-20 mA, HART 5/7
Supply Pressure 1.4 – 6 bar (20 – 87 psi)
Air Consumption < 0.03 kg/h (steady state)
Linearity Error ±0.5% of span (verified on test bench)
Dead Band 0.1%
Stroke Range Linear 5–130 mm / Rotary 30–100°
Operating Temperature -40 °C to +80 °C
Protection Class IP66 / NEMA 4X
Housing Material Aluminum, painted
Pneumatic Connection G 1/4 female
Electrical Connection M20 × 1.5 cable gland
Weight Approx. 1.7 kg
Output Capacity 5.0 kg/h at 1.4 bar supply
Repeatability ±0.1% (measured, 100-cycle run)

Installation Guide

Mount the positioner on the actuator yoke with the supplied bracket and set the feedback lever to valve mid-stroke. Field surveys show that a 1.4–6 bar supply plus a 4-20 mA calibrator check catches most zero and span errors before startup. Keep cable bending radius above 50 mm and route signal wiring away from high-voltage lines. Use an M20 gland rated IP66 on non-Ex models. Run auto-calibration from the local buttons or a HART handheld before commissioning.

Engineering Advantages

The TZIDC platform uses a non-contact magnetoresistive sensor that shrugs off vibration and wear, and a 100-cycle repeatability test holds ±0.1%. The painted aluminum housing resists corrosive plant air, especially with the optional protective filter. HART diagnostics report valve signature, travel deviation, and supply pressure trends so you can plan maintenance. The unit drops straight into ABB 800xA and third-party DCS via standard 4-20 mA loops.

Technical FAQs

Q1: How do I verify the zero position?
A1: Apply 4 mA and confirm the valve sits at 0% stroke; the display should read 0.0 ±0.5%. Turn the zero screw if it drifts past that band.

Q2: Does this model support HART configuration?
A2: Yes. The 02 code enables HART 5/7 for remote parameter setting, diagnostics, and valve signature capture from a handheld or DCS.

Q3: What is the maximum supply pressure?
A3: Keep it at or below 6 bar (87 psi). Higher pressure risks actuator seal damage and voids the IP66 rating.

Product Resources

📄 Download PDF
  • Perak

Skalar (V/f)

Vektor

Dikuasakan oleh AC

  • Sahkan model tepat, nombor bahagian, dan spesifikasi sebelum membuat pesanan.
  • Pastikan keserasian dengan mesin atau sistem kawalan anda sekarang.
  • Hubungi melalui sale@etowonauto.com atau +8617859788089 untuk bantuan teknikal.
  • Semak pilihan penghantaran, masa penghantaran, dan keperluan penghantaran.
  • Ikuti arahan pengeluar dan amalan terbaik semasa pemasangan.

Barangan yang ada dalam stok biasanya dihantar pada hari perniagaan yang sama. Untuk produk yang tidak tersedia dalam stok, masa penghantaran mungkin berbeza bergantung pada ketersediaan. Penghantaran antarabangsa disediakan, dan kos penghantaran dikira mengikut destinasi, berat, dan pilihan pengangkut.

Pengembalian diterima dalam tempoh 30 hari selepas penerimaan, dengan syarat barangan tidak digunakan dan dalam keadaan asal. Kos penghantaran untuk pengembalian adalah tanggungjawab pelanggan. Sila hubungi kami sebelum memulangkan sebarang barangan untuk mendapatkan kebenaran pengembalian.

Untuk maklumat lanjut, sila semak Polisi Penghantaran & Pengembalian.

Lihat Butiran Produk

PASTIKAN PRESTASI MESIN YANG BOLEH DIPERCAYAI

Ubah rumah anda dengan penyelesaian multi-elektronik terkini, dari pencahayaan pintar hingga peranti kawalan suara — semua direka untuk memudahkan hidup, menjadikan ia lebih selamat, dan lebih berhubung. Optimumkan operasi anda dengan Sistem Pemantauan Bently Nevada 3500, yang menawarkan pemantauan getaran dan keadaan mesin secara masa nyata untuk mencegah kerosakan dan memaksimumkan masa operasi.